Seiko STOPWATCH S143 Guía para resolver problemas descargar pdf (Pagina 14)

15.SPECIFICATIONS

(Stopwatch)

１.Frequency of crystal …………………32,768Hz (Hz＝Hertz…Cycles per

second)

２.Loss/gain ………………………………Less than 15 seconds at normal

temperature range (5℃∼35℃)

３.Operational temperature ……………−10℃∼＋60℃

Desirable temperature ………………０℃∼＋50℃

range of use

４.Display system ……………………… Stopwatch display Measures up to

10 hours. Hour, minutes, seconds,

1/100 seconds, tnree-row display of

split time/lap time/total elapsed time or

lap time in prooress. No. of blocks, no.

of split times (0∼999), 300 memory

recall, BLOCK, SPLIT, LAP, STOP,

RECALL, stopwatch marks, memory

indicator, BATT.

Time/calendar display Hour (24hour

indication), minutes, seconds, year,

month, date and calendar mark, ID no.

(OFF/01∼99), contrast adjustment

display.

Auto start set display AS, OFF, ON,

hour, minutes, seconds, 1/100

seconds, auto start set mark.

５.Display medium ………………………Nematic Liquid Crystal, FEM (Field

Effect Mode)

６.Battery …………………………………Lithium battery SB-T74, 1 piece

７.Battery Life ……………………………A new normal battery will last

approximately three years.

＊

If the stopwatch is used for more than 3

hours a day, the battery life may be less

than 3 years.

８.IC (Integrated Circuit) ……………C-MOS-LSI, 1 piece

９.Battery life indicator ……………"BATT" mark start flashing when

the battery life nears its end.

(Printer)

１.Printer ……………………………Model: MTP102

Printing system: Thermal serial dot

printing system

Printing method: One-way printing

(from left to right)

Printing speed: Approx. 1.5

lines/sec. (DC 5 0V. at 25℃)

Number of digits printed: 13

digits/line (including space)

２.Recording paper …………………Roll paper S-950

38mm (width) (＋ 0∼ 0.5mm),

overall length 2,400 mm or more

(approx. 700 lines can be printed

per roll.)

３.Power supply ……………………DC 6.0V (SUM-3 or AM3 dry

battery, 4 pieces)

With power switch turned "ON" (No

printing) : Approx. 0.02W (DC 6.0V)

４.Power consumption ……………During printing: Approx. 1.5W (DC

6.0V)

５.Battery life ………………………Manganese battery: Approx.

10,000 lines can be printed.

(Equivalent to approx. 14 rolls)

Alkaline manganese battery:

Approx. 20,000 lines can be

printed. (Equivalent to approx. 28

rolls)

６.Operational temperature range…0℃∼40℃ (The depth of printout

does not change even if the

temperature changes.)

＊The above specifications are subject to change without prior notice, for

product improvement.

oscillator

(monthly rate)

range.

14.TROUBLESHOOTING GUIDE

Before requesting service, please check your stopwatch following the table below.

Problem Possible cause Solution Problem Possible cause Solution

The motor does not run

even if the power switch

of the printer is turned

"ON".

The paper is not

advanced by pressing

the paper advancing

switch.

By pressing the start

button, the paper is

advanced, but the

printed digits or letters

are detective or the data

are not printed at all.

●Weak batteries.

●The batteries are not

installed properly.

●The paper is stuck.

●Weak batteries.

●The paper is stuck.

●The roll paper gets out

of shape.

●The cord is not con-

nected properly.

●Water or foreign

matters are sticking to

the cord plug.

●The paper is not set

properly.

●Replace the batteries

with new ones.

●Install the batteries

properly.

●Remove the paper.

●Replace the batteries

with new ones.

●Remove the paper.

●Make the roll paper

round.

●Connect the cord

correctly.

●Wipe off the water or

foreign matters.

●Inset the paper

properly.

By pressing the start

button, the data are

printed out, but the paper

is not advanced irregu-

larly.

By pressing the start

button, no data are

printed out and the paper

is not advanced at all.

Auto start time is not

transferred.

●The paper is stuck.

●Weak batteries.

●The batteries are not

installed properly.

●The power switch of

the printer is not set to

"ON".

●The cord is not connect-

ed properly.

●Water or foreign matters

are sticking to the cord

plug.

●Remove the paper.

●Replace the batteries

with new ones.

●Replace the batteries

with new ones.

●Insert the batteries

correctly.

●Turn the power switch

"ON", and then press the

start button.

●Connect the cord prop-

erly.

●Wipe off water or for-

eign matters.

＊For the solution of trouble other than the above, contact the retailer from whom the watch was purchased.

1 2 ... 9 10 11 12 13 14

Comentarios a estos manuales

Sin comentarios

Seiko STOPWATCH S143 Guía para resolver problemas Pagina 14

Comentarios a estos manuales