Seiko STOPWATCH S143 Guía para resolver problemas descargar pdf (Pagina 7)

●Memory data guide during recall

While the data is recalled, a segment of the

bar flashes to indicate the measurement

order of the data being recalled.

In the illustration below, 210 to 239 data is

stored in memory and the data being

recalled is between 120th and 149th

data in memory.

■Notes on memory capacity

・The number of data in memory is shown

graphically by the memory capacity

indicator.

・Besides the measured lap times/split

times, the start time data and block

number are also retained in memory as

two separate data. Therefore, a block of

data includes at least three data. If more

than one block is used to store the data,

the memory become full even before the

number of lap time/split time

measurements in memory amounts to

300.

SPLIT

RECALL

BLOCK

LAP

STOP

BATT.

LAP

●How to read the memory capacity

indicator

The number of data stored in memory is

displayed graphically with a 10-segment

bar.

Each segment of the bar corresponds to 30

data. The segments are displayed one

by one from the bottom to indicate the

number of data in memory.

●When the memory reaches its full

capacity:

・All the segments of the bar are

displayed.

・The 301st data and those measured

thereafter will be displayed but will not be

stored in memory for later recall.

SPLIT

RECALL

BLOCK

LAP

STOP

BATT.

LAP

It flashes.

Number of data in memory

When 10 or less data of

memory capacity is

available, the top segment

starts flashing. When the

memory is at its full

capacity, it stops flashing

and remains displayed.

30 to 59 data is stored in

memory. When no segment

is displayed, 0 to 29 data is

stored in memory.

290∼300

270∼290

240∼269

210∼239

180∼209

150∼179

120∼149

90∼119

60∼ 89

30∼ 59

６.HOW TO PRINT OUT

1.How to set the paper in the printer

●Besides the thermal paper S950 included

with this model, the thermal paper S951 is

available for printing out the stored data. It is

a long-type thermal paper that can print

out up to 2,800 lines, and sold for ¥578.

To use S951, the paper holder SVAZ007

for exclusive use with it is necessary. It is

sold separately for ¥3,990.

□

１

Cut the first pasted position of the paper

straight.

□

２

Open the paper cover as shown in the

illustration.

□

３

Slide the power switch to "ON". At this

time, the motor runs for approximately 1

second to indicate that the power is

supplied.

□

４

Inset the end of the paper into the paper

insertion slot.

□

５

Keep the paper advancing switch pressed

until the end of the paper is advanced out 2

to 3 cm from the printer.

(Do not pull out the paper by force.)

□

６

Put the roll paper into the holder and

close the paper cover.

Be sure to set the paper with the right side up. It

can only be printed on one side.

（）

If the roll paper gets out of shape, make it round

before inserting it into the holder.

（）

Notes 1 Do not pull the paper in the reverse direction (opposite to the direction of

advancing the paper), as this will damage the printer. When replacing the

remaining roll paper with a new one, first cut the paper in the holder, then

remove the rest of it by pressing the paper advancing switch, or pull it out

in the direction of advancing the paper.

Notes 2 Be sure to use the roll paper S-950 for exclusive use with this model.

Otherwise, poor printing or malfunction will be caused.

Roll paper

Power switch

Paper advancing

switch

２.Printout

Printout during the measurement

□

１

Turn on the power switch for printer before starting

the measurement. When the switch is turned on, the

roll paper is advanced by one line.

□

２

Operate print mode selection switch to select the

printout from "lap time only" and "both split time and

lap time".

SYSTEM STOPWATCH

POWER

Print mode

selection

switch

Power switch

LAP

SPLIT

Both split time and lap time are printed out.

(print mode selection switch)

Only split time is printed out.

□

３

After the measurement is started, the identification number (if it is set), block

number, starting time, date, month and year are printed out, and then the

time data are printed out successively as soon as they are measured.

LAP

SPLIT

Block number BLOCK:1

Year･Month･Date 1999 10 10

Start time START 10:19

SPLIT

1-0:05′03 76

2-0:05′12 33

3-0:05′41 13

4-0:05′59 06

5-0:06′17 88

6-0:06′43 56

7-0:07′21 47

8-0:07′36 48

Finish time /S/0:08′02 58

Block number BLOCK:1

Year･Month･Date 1999 10 10

Start time START 10:19

SPLIT/LAP

1-0:18′05 33

0:18′05 33

2-0:36′37 78

0:18′32 45

3-0:55′13 11

0:18′35 33

4-1:13′25 31

0:18′12 23

5-1:31′57 55

0:18′32 21

6-1:49′32 78

0:17′35 23

7-2:01′31 04

0:17′58 26

8-2:25′43 62

0:18′12 58

Finish time /S/2:54′02 77

Example of printout

Print mode

selection

switch

Split time only

Both split time and

lap time

＊When the power switch of the printer is turned on after the measurement is started, the data is printed

out starting from the next measurement data.

LAP

SPLIT

Split time

Lap time

1 2 3 4 5 6 7 8 9 10 11 12 13 14

Comentarios a estos manuales

Sin comentarios

Seiko STOPWATCH S143 Guía para resolver problemas Pagina 7

Comentarios a estos manuales