Seiko DPU-414 Guía de usuario

USER'S GUIDE Thermal Printer DPU-414 Read this manual carefully before using the printer. Keep this manual in a place where it c

Be sure to hold the battery cover to the printer when the battery pack is inserted in the printer. Fall of the battery pack due to the battery cover

Precautions in the Battery pack (Option) WARNING If you find any of the following abnormalities in the battery pack, remove the battery pack from th

DO NOT apply strong impact to the battery pack with a hammer or a nail, and DO NOT crush it. Doing so may cause liquid leakage, explosion, overheati

OPERATING PRECAUTIONS Please follow the precautions below to enjoy and maintain the full performance of the printer. Using the printer  Be careful

 Always use the specified thermal paper TP-411L. Installation  Install the printer in a flat, stable place.  Do not install the printer in the

- 11 - NOTATIONS USED IN THIS MANUAL The following two types of notations are used throughout this manual to denote items of caution and items to

- 12 -1 PREPARATION 1.1 Unpacking Once you have opened the carton, make sure it contains the printer and all accessories. The standard configurati

1.2 Part Names Front Paper coverwindowPaper coverPower LEDPower Switch Back Power supply jackGround screwParallel inputconnectorSerial inputconnecto

1.3 Operation Panel OFFLINE LED ONLINE button FEED button Power Switch Power LED ONLINE LED 1 Power Switch Slide the Power Switch to turn the po

 DO NOT press and hold the ONLINE button and FEED button for 30 seconds or more, because it will cause the Software DIP switches to reset and you wi

DPU-414 THERMAL PRINTER USER'S GUIDE U00120592100 June 2010 U00120592101 October 2011 U00120592102 February 2012 U00120592103 March 2012 U0012059

- 16 -2 OPERATION 2.1 Connecting AC Adapter 1. Turn off the power. 2. Plug the DC plug on the AC adapter into the power supply jack on the

2.2 Loading the Thermal Paper Opening and Closing the Paper Cover 1. Lightly push up on the front of the paper cover with your thumb and rotate it

Loading the Thermal Paper 1. Turn on the power. Paper2. Cut the tip of the thermal paper straight across. New paper can be inserted as is. (See fi

2.3 Setting the Software DIP Switches (SWDIP switch) The startup settings and input method can be set by the Software DIP switches (SWDIP switch).

complete!!" is printed out and the printer returns to ONLINE mode. 6. As soon as switch number 8 of SWDIP switch 3 is set, the printer writes th

2.4 SWDIP Switch Settings (1) SWDIP switch 1 indicates factory default setting. Switch No. Function ON OFF 1 Input Method Parallel Serial 2 P

(2) SWDIP switch 2 Switch No. Function ON OFF 1 Print mode Normal printing (40 columns) Condensed printing (80 columns) 2 User-defined characters

(3) SWDIP switch 3 Switch No. Function ON OFF 1 Data bit length 8 bits 7 bits 2 Parity permission Without With 3 Parity condition Odd Even 4

2.5 Connecting the Printer Connection 1. Turn off the printer and computer. 2. Connect the printer to the computer with an interface cable. Pa

Parallel Serial - 25 -

Applicable EC Directive and Standards Product: Thermal Printer DPU-414-40B-E, DPU-414-41B-E Directive: Title 2004/108/EC EC Electromagnet

2.6 Test Print In a test print, characters 20H to FEH are printed in condensed, ordinary and double-width modes according to the international, spec

2.7 HEX Dump Print Data input from the computer is printed in hexadecimal codes and in characters to allow you to check if data has been input corr

2.8 Printing 1. Turn on the power to the printer and the computer. 2. Check that the ONLINE LED lights. When the thermal paper is not set, the OFF

2.10 Handling the Battery Pack A fully charged battery pack can print about 3000 lines (40 columns of the number "8"). The battery dischar

Removing the Battery Pack 1. Remove the battery cover as shown in Figure 1. 2. Pull out the battery pack, grab the connector with your thumb and inde

When the Battery pack Gets Low During Printing When the Power LED starts blinking about once every 0.5 seconds and the printer goes OFFLINE, connect t

3 PRINTER FUNCTION 3.1 Buffer Full Printing The DPU-414 has a line buffer to receive data in one-line units. If data with more columns than one

- 33 -If an error occurs: A or B: 1. Turn off the Power Switch. 2. Remove the foreign material. 3. Turn on the Power Switch. C: Use the pri

4 CONTROL CODE The DPU-414 uses control codes to change forms and characters. The control codes are not printed. There are two types of functi

E SC sequence codes Code Function ESC+ "%" +n Select user-definable characters ESC+ "&" +s+n Register user-definable charact

Federal Communications Commission (FCC) compliance statement This equipment has been tested and found to comply with the limits for a Class B digital

5 CHARACTER CODE TABLE  Japanese Character Set The following table is the Japanese character set when 0 is set to normal 0. • Function codes

 IBM Character Set The following table is the English character set when 0 is set to normal 0 . Upper 4 bits Lower 4 bits • SP denotes space.

- 38 -6 SPECIFICATIONS 6.1 General Specifications Printer specifications Printing method: Thermal serial dot Character mode Total number of dots:

- 39 - Specifications of Specified AC Adapter (Option) Item Specifications Product No. PW-C0725-W1-x*1 Input AC100 V to AC240 V 50 Hz to 60 Hz Ou

- 40 - List of Compliance with Regulation Please check the list below to see if the printer and its accessories can be operated in destination count

- 41 -6.2 Interface Specifications Parallel (1) Specifications Data input: 8 bits parallel (Centronics) Handshake: STROBE , BUSY, and ACK (2)

- 42 -(3) Data Input Timing (Unit: s, typical) 5.34.81.00.5 Min.0.5 Min.0.5 Min.DATA 0DATA 7STROBEBUSYACK (4) Signal Conditions Standard Item Mi

- 43 -Serial (1) Specifications Data input: RS-232C Data control: H/W BUSY, XON/XOFF (2) Connector signal description Pin no. Signal I/O Funct

- 44 -(3) Error processing The following characters are printed when an error occurs. ? (3FH): Framing error ! (21H): Parity error * (2AH): Overru

- 45 - 7 TROUBLESHOOTING Check the following points if the printer has malfunctioned or does not operate at all. If it has still problems, call

- 1 - INTRODUCTION Thank you for purchasing the DPU-414 thermal printer. This USER'S GUIDE explains how to handle DPU-414 thermal printer

- 46 -If the printer does not print or stops during printing Checkpoint Action Reference page Is the OFFLINE LED flashing? The thermal paper has run

- 47 -If the printer prints wrong characters Checkpoint Action Reference page Is interface cable connected correctly? See Section 2.5. 24 Are the S

- 48 -8 CARING FOR THE DPU-414 PRINTER If the outside of your printer gets dirty, wipe it with a soft, dry cloth. If it gets very dirty, wet

Seiko Instruments Inc. 1-8, Nakase, Mihama-ku, Chiba-shi, Chiba 261-8507, Japan Print System Division Telephone:+81-43-211-1106 Facsimile

SAFETY PRECAUTIONS The following symbols are used in this manual in order to make use of the printer properly and prevent the printer from being d

Precautions in the Printer WARNING DO NOT use the printer, the AC adapter and the AC cable in countries where these items do not comply with the reg

DO NOT put the printer into water in a place where it could get wet. Doing so may cause fire, a failure or other accidents. DO NOT touch the pri

CAUTION If the printer is not used for a long time, unplug the AC plug from the outlet and remove the battery pack from the printer. If not, it might