Seiko DPU-S245-01A-E Guía de usuario

USER’S GUIDE Thermal Printer DPU-S245 SERIES Read this user’s guide carefully before using the printer. Keep this user’s guide in a p

- 5 - CAUTION If the printer is not used for a long time, unplug the AC plug from the outlet and remove the battery pack from the printer. If not, i

- 6 - DO NOT touch the cutter. Doing so may cause injury. Be sure to hold the battery cover to the printer when the battery pack is inserted in t

- 7 - Precautions in the Battery pack (Option) WARNING If you find any of the following abnormalities in the battery pack, remove the battery pack

- 8 - DO NOT apply strong impact to the battery pack with a hammer or a nail, and DO NOT crush it. Doing so may cause liquid leakage, explosion, over

- 9 - OPERATING PRECAUTIONS Please follow the precautions below to enjoy and maintain the full performance of the printer.  Using the Printer 

- 10 -  When the battery pack is used at low temperature, the length of time the printer can be used may be shortened.  High-print-rate printing o

- 11 -  Notations Used in this User’s Guide The following two types of notations are used throughout this User’s Guide to denote items of caution an

- 12 - 1 PREPARATION Once you have opened the carton, make sure it contains the printer and all accessories. Keep the package and packing m

- 13 - 2 EACH PART OF PRINTER (1) POWER switch The POWER switch turns the printer ON or OFF. To turn the printer on, hold down the POWER switch

- 14 - (6) Interface connector The interface connector connects with the interface cable. Open the rubber cover and insert the connector. (7) Paper

DPU-S245 SERIES THERMAL PRINTER USER’S GUIDE Document Number: U00117065201 First Edition: July 2009 Second Edition: January 2010 Copyright 2

- 15 - Lamp Display Lamp display POWER lamp (Green) ERROR lamp (Orange) Power OFF Off Off Power ON (Print-ready) On Off Initializing On On Out

- 16 - 3 POWER CONNECTION The printer can be powered with a battery pack or an AC adapter. Always refer to Section 11 SPECIFICATIONS before using th

- 17 - HINT  If the battery pack starts to run out soon, it means that the battery life has expired. Purchase a new battery pack.  When used in

- 18 -  Connecting the AC Adapter (1) Connect the AC cable to the AC adapter. (2) Insert the DC jack of the AC adapter to the power connector of the

- 19 - 4 PAPER SETTING This printer can feed the paper roll. The printer function setting for cut sheets is different from that for paper roll. Se

- 20 - 5 TEST PRINTING After setting the thermal paper in the printer, perform test printing. In test printing, the printer's function setting

- 21 - 6 FUNCTION SETTING This printer can be set various function according to operating conditions or uses. The settings are stored in the softwa

- 22 - HINT  The printer enters the HEX Dump mode by pressing the POWER switch. This mode can be checked to see the printer's transmission stat

- 23 - (2) Changing SWDIP switch settings When the message shown at the following is printed in the function setting mode, press the POWER switch

- 24 - Operation 2: SWDIP switch setting (1) When the message shown at the following is printed, set the bits from the most significant bit (SWDIP*-8)

Product: Thermal Printer DPU-S245-00A-E, DPU-S245-01A-E Directive: Title 2004/108/EC EC Electromagnetic Compatibility Directive Standards EN 55022

- 25 - Operation 3: Exiting function setting mode If pressing the FEED switch when the message shown at the following is printed, the printer return

- 26 -  SWDIP Switch Setting List : Default settings SWDIP switch 1 SW DIP Function Setting 1 Busy 1-8 Data control 0 Xon/Xoff 1 1 bit 1-7 Stop Bi

- 27 - SWDIP switch 2 SWDIP Function Setting 1 Disable 2-8 Auto Status Output 0 Enable 1 JIS code 2-7 Kanji Code 0 Shift-JIS Code 1 24 dots 2-6 F

- 28 - SWDIP switch 3 SW DIP Function Setting 1 Mark Roll Paper *2 3-8 Paper Mode 0Roll Paper 3-7 0 0 11 3-6 Print Density *3 095% 1 100% 0105% 1 110

- 29 - SWDIP switch 4 SW DIP Function Setting 1 Disable 4-8 Bluetooth Link Key selection*4 (Bluetooth Link Key)0 Enable 4-7 Reserved 1 Fixed to 1 1

- 30 - 7 CONNECTING TO THE HOST DEVICE This printer supports serial and USB communication through an interface cable and infrared communication whi

- 31 -  Serial/USB Communication with an Interface Cable (1) Turn the printer off. (2) Open the interface connector cover and connect the interfac

- 32 -  Infrared communication by IrDA (1) Turn the printer off. (2) Turn the printer on without connecting the USB interface cable to it. (3) Pl

- 33 -  Bluetooth-based Wireless Communication (Bluetooth-supporting model) (1) Turn the printer off. (2) Turn the printer on without connectin

- 34 - 8 RECHARGING THE BATTERY PACK The battery pack is partially charged prior to shipping, and provides sufficient power to check the printer ope

Federal Communications Commission (FCC) compliance statement This equipment has been tested and found to comply with the limits for a Class B digital

- 35 - HINT  The printer can print or receive data while it is recharging the battery pack. During printing or receiving data, the POWER lamp light

- 36 - NOTE - When the battery charger is connected to the outlet, do not bring any metal object into contact with the metal terminal. - Unplug the

- 37 - 9 THERMAL HEAD MAINTENANCE The thermal head of this printer does not require user maintenance. If paper powder accumulates, clean the therm

- 38 - 10 TROUBLESHOOTING Check the following points before you make a request for repair.  The power does not turn on. · Is specified AC adapt

- 39 - 11 SPECIFICATIONS  Printer Specifications Item Specification Model DPU-S245-00A-E (Bluetooth-unsupporting model) DPU-S245-01A-E (Bluetoo

- 40 -  Interface Specifications · Serial interface Item Specification Synchronous Asynchronous Baud rate 1200, 2400, 4800, 9600, 19200, 38400,

- 41 -  List of Compliance with Regulation Please check the list below to see if the printer and its accessories can be operated in destination coun

- 42 - 12 OPTIONS AND CONSUMABLE PARTS  Options Name Model Specified Battery pack BP-L0715-A1-E Specified AC adapter PW-0904-W2-E Specified Ba

- 43 -  Thermal Paper line Model Specification TP-S245L-1 58 mm width, 38mm diameter roll  Specified Thermal Paper line *1 Model Manufactu

Seiko Instruments Inc. 1-8, Nakase, Mihama-ku, Chiba-shi, Chiba 261-8507, Japan Print System Division Telephone:+81-43-211-1106 Facsi

Industry Canada (IC) compliance statement Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) t

- 1 - INTRODUCTION Thank you for purchasing the DPU-S245 thermal printer. This USER’S GUIDE explains how to handle DPU-S245 thermal printer (herein

- 2 - SAFETY PRECAUTIONS The following symbols are used in this User’s Guide in order to make use of the printer properly and prevent the printer fr

- 3 - WARNING DO NOT use the printer, the AC adapter, the AC cable and the battery charger in countries where these items do not comply with the reg

- 4 - DO NOT connect except specified battery pack with the battery charger. Doing so may cause explosion, overheating or fire leading to fire or in