Seiko LTP F Series Especificaciones

ACU F SERIES AUTOCUTTER UNIT TECHNICAL REFERENCE U00060421405 Seiko Instruments Inc.

2222----１１１１ CHAPTER 2 FEATURES The ACU F Series is a sliding type freely adjustable automatic cutter. This autocutter enables freely paper

3333----１１１１ CHAPTER 3 SPECIFICATIONS 3.1 GENERAL SPECIFICATIONS Table 3-1 lists the general specifications of the autocutter. Table 3-1

3333----２２２２ 3.2 PAPER CUTTING CONDITIONS This autocutter has two types of paper cutting methods: full cutting and leaving one point without cu

3333----３３３３ 3.3 DETECTOR (CONTROL SWITCH) AND MOTOR SPECIFICATIONS (1) Detector... for detecting the home position • Rate

4444----１１１１ CHAPTER 4 DRIVE METHOD 4.1 SAMPLE DRIVE CIRCUIT 3 1 4 + TA8428K 2 Cutter Unit 1kΩ A (Motor Drive Signal) B (Motor Drive Si

4444----２２２２ 4.2 MOTOR DRIVE SEQUENCES Table 4-1 lists the motor drive sequences. Table 4-1 Motor Drive Sequences (For Figure 4-1

4444----３３３３ 4.3 FLOWCHART FOR DRIVING Figure 4-2 shows flowchart for driving. Figure 4-2 Flowchart for Driving Detector OFF DETECTOR O

4444----４４４４ 4.4 TIMING CHART FOR DRIVING FOR DRIVE CIRCUIT Figure 4-3 shows timing for driving. Figure 4-3 is driving timing in the driving

5555----１１１１ CHAPTER 5 CANCELING MOTOR (MOVABLE BLADE) LOCK If the autocutter locks up due to a paper jam while cutting paper, power off t

6666----１１１１ CHAPTER 6 CONSIDERATIONS WHEN MOUNTING THE AUTOCUTTER The autocutter is for an exclusive use of our LTP F Series Thermal Prin

ACU F AUTOCUTTER UNIT TECHNICAL REFERENCE Document Number U00060421405 First Edition August 2001 Second Edition January 2002 Third Edit

6666----２２２２ 6.2 MOUNTING FIXED BLADE The fixed blade mounting differs on the model. Refer to Figure 6-2-1 for ACUF224A-E, ACUF224B-E, ACUF324

6666----３３３３ Figure 6-2-2 Mounting Fixed Blade Unit (ACUF224C-E, ACUF224D-E, ACUF324C-E, ACUF324D-E) 爪爪爪爪 Screws

6666----４４４４ 6.3 THE AUTOCUTTER MOUNTING DIRECTION Mount the autocutter as shown in Figure 6-3 (A), (B) and (C). When the autocutter is used i

6666----５５５５ 6.4 CONSIDERATIONS FOR OUTER CASE DESIGN (1) The outer case of the paper outlet side of the autocutter should be designed so that

6666----６６６６ Unit: mm Figure 6-5 Sample Outer Case (Movable Blade Unit Side)

6666----７７７７ 6.5 CONSIDERATIONS FOR USING (1) Do not back feed paper after cutting paper using the autocutter because it will cause a paper j

6666----８８８８ 6.6 CORRESPONDENCE WITH OUR LTP F SERIES THERMAL PRINTERS Table 6-1 shows correspondence with our LTPF series thermal printers for

7777----１１１１ CHAPTER 7 APPEARANCE Figure 7-1 shows the appearance and the external dimensions of the ACUF224A-E and ACUF224B-E autocutter

7777----２２２２ Figure 7-1 Appearance (ACUF224A-E, ACUF224B-E) Unit: mm General tolerance of unit exterior: ±0.8 Tolerance between screw and bos

7777----３３３３ Figure 7-2 Appearance (ACUF324A-E, ACUF324B-E) Unit: mm General tolerance of unit exterior: ±0.8 T

iiiiiiiiiiii PREFACE This reference manual describes the specifications and basic operating procedures for the ACU F Series Au

7777----４４４４ Figure 7-3 Appearance (ACUF224C-E, ACUF224D-E) Unit: mm General tolerance of unit exterior: ±0.8 T

7777----５５５５ Figure 7-4 Appearance (ACUF324C-E, ACUF324D-E) Unit: mm General tolerance of unit exterior: ±0.8 T

iviviviv TABLE OF CONTENTS Section Page CHAPTER 1 PRECAUTIONS 1.1 SAFETY PRECAUTIONS...

vvvv CHAPTER 5 CANCELING MOTOR (MOVABLE BLADE) LOCK CHAPTER 6 CONSIDERATIONS WHEN MOUNTING THE AUTOCUTTER 6.1 MOUNTING THE MOVABLE

vivivivi FIGURES Figure Page 3-1 Paper Cutting...

viiviiviivii TABLES Table Page 3-1 General Specifications...

1111----１１１１ CHAPTER 1 PRECAUTIONS 1.1 SAFETY PRECAUTIONS The autocutter is an exclusive autocutter for SII’s LTP F Series thermal printer m

1111----２２２２ 1.2 DESIGN AND HANDLING PRECAUTIONS 1.2.1 Design Precautions • Connect the FG line to the screw hole on the back of the autocut