Seiko RP-E10 Series Guía de usuario

USER’S GUIDE Thermal Printer RP-E10 SERIES Read this user’s guide carefully before using the printer. Keep this user’s guide in a pla

- 7 - 1 PREPARATION When you open the carton, make sure it contains the printer and its accessories. 本体（上紙排出モデル）本体（前紙排出モデル）安全上の注意 1枚取扱説明書/安全上の注意/各種ソフ

- 8 - Models including the AC adapter, AC cable, and interface cable are also available. Keep the package and packing materials for future transporta

- 9 - 2 IDENTIFYING THE MODEL TYPE The printer model is identified as follows: RP-E10-K3FJ1-U1C3 Direction of paper discharge 0: From the top 1: F

- 10 - 3 EACH PART OF PRINTER 125364上面排紙モデル1378910121114Top paper discharge model

- 11 - 6435211012111413789前面排紙モデルFront paper discharge model 1616 181715USBモデルシリアルモデルUSB+シリアルモデル16イーサネットモデルUSB modelSerial modelUSB + Serial modelEth

- 12 - (1) POWER switch The POWER switch turns the printer ON or OFF. The LED lights when the printer turns ON. To turn the power OFF, hold down the s

- 13 - LED Display LED Indication LED (Color) LED (Lighting Pattern) Power OFF - Off Power ON (print-ready) Blue*1 On*1 Printing Green On Paper-n

- 14 - 4 POWER CONNECTION This printer can be powered with an AC adapter. Always refer to "15 SPECIFICATION" before using the AC adapter.

- 15 - 5 THERMAL PAPER SETTING This printer uses the paper roll (hereinafter referred to as thermal paper). The function settings of the printer dep

- 16 - (4) Pull the thermal paper straight and then push the center of paper cover certainly to close it, to avoid one side lock defect. ○○××Top pap

RP-E10 SERIES THERMAL PRINTER USER’S GUIDE Document Number: U00127526501 First Edition: May 2012 Second Edition: July 2012 Copyright 2012 by

- 17 -  Recommended Thermal Paper Shape ○×× NOTE - DO NOT use deformed thermal paper. Doing so may cause the printer damaged. NOTE - In case of

- 18 - 6 ADJUSTMENT OF REMAINING THERMAL PAPER This printer detects remaining amount of the thermal paper by the paper-near-end sensor. Detecting the

- 19 - ペーパニアエンドセンサペーパニアエンドセンサ設定レバー　Ａ　Ｂペーパニアエンドセンサペーパニアエンドセンサ設定レバー　C D【上紙排出モデル】【前紙排出モデル】 Paper-near-end Sensor Position Outside Diameter for Paper-nea

- 20 - 7 PREVENTION AND TREATMENT OF PAPER JAM Do not touch the paper outlet during paper feeding or before paper cutting. Covering the paper outlet

- 21 - Cutter Error Treatment When the motor is locked during paper cutting due to a cutter error and the paper cover does not open, recover the p

- 22 - 8 TEST PRINT This printer has a test printing function. In test printing, the function settings of the printer and character strings for testi

- 23 - 9 FUNCTION SETTINGS This printer has various functions which can be preset according to the communication method or the type of thermal paper.

- 24 - 10 CONNECTING TO THE HOST DEVICE This printer supports the serial, USB, USB + serial, or Ethernet communication, depending on the model, throu

- 25 - Ethernet interface cable NOTE - When connecting an interface cable to the interface connector, push it until it clicks. - DO NOT connect plu

- 26 - Connecting to the Drawer (1) Turn the printer OFF. (2) Connect the plug of drawer kick cable to the drawer kick connector on the backsid

Federal Communications Commission (FCC) compliance statement This equipment has been tested and found to comply with the limits for a Class A digital

- 27 - 11 SETTINGS WHEN USING 58mm PAPER WIDTH (1) Turn the printer OFF. (2) Pull the release lever to open the paper cover. (3) Remove the coin

- 28 - 12 WALL MOUNTING KIT (WLK-B01-1) The Wall Mounting Kit is exclusive for the Front paper discharge model. It cannot be used for the Top paper d

- 29 - (2) Installation of Printer Bracket Fix it with four attachment screws certainly as shown in the following figure. The tightening torque shou

- 30 - (4) Installation of the Printer Slide the printer into the wall hanging bracket from the top to the bottom to insert the printer bracket into

- 31 - 13 PRINTER MAINTENANCE The thermal head of this printer does not require user maintenance. If paper powder accumulates, clean the thermal head

- 32 - 14 TROUBLESHOOTING Check the following points before requesting for repair: The power does not turn ON • Is specified AC adapter being us

- 33 - 15 SPECIFICATION Printer Specifications Item Specification Model RP-E10, RP-E11 Printing method Thermal Characters per line*1 Paper width

- 34 - Interface Specifications Serial interface specifications Item Specification Synchronous Asynchronous Baud rate 9600, 19200, 38400, 115200 bp

- 35 - Compliance Table Check the list below to see if the printer and its accessories can be operated in destination countries and comply with the

- 36 - 16 ACCESSORIES AND CONSUMABLE PARTS Accessories Name Model Specified AC adapter PW-E2427-W1 Specified AC cable*1 For Japan CB-JP03-20A Fo

- 1 - INTRODUCTION Thank you for purchasing the RP-E10 series thermal printer. This MANUAL explains how to handle RP-E10 thermal printer (hereinafter

Seiko Instruments Inc. 1-8, Nakase, Mihama-ku, Chiba-shi, Chiba 261-8507, Japan Print System Division Telephone:+81-43-211-1106 Facsi

- 2 - SAFETY PRECAUTIONS The following symbols are used in this Safety Precautions to ensure safe and proper use of products and to alert users. Obse

- 3 - OPERATING PRECAUTIONS Warning Never attempt! Strictly observe the following instructions. Failure to follow the instructions leads to fire, e

- 4 - How to deal with trouble Follow the instructions in the following cases. Failure to follow the instructions may lead to fire, electric shock, a

- 5 - OPERATING PRECAUTIONS Follow the precautions below to deliver and maintain the full performance of the printer. Using the Printer ♦ Be car

- 6 - ♦ DO NOT use two or more thermal papers which are taped together. ♦ NEVER pull out the thermal paper during the thermal paper setting. ♦ Make